I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
In my application I have a requirement to send notifications to mobile on triggering particular Interrupts as well as particular events.I have created a customised notification...
Supported tx_power values: -40dBm, -20dBm, -16dBm, -12dBm, -8dBm, -4dBm, 0dBm, +3dBm and +4dBm.
What is difference in the behavior of nrf 52832 chip for these different...
We're developing Bluetooth tags that we would like to operate at both 1Mbps and coded (long range). From what I've read and seen from the Nordic testing, specifically "Testing...
I modified the gpio interrupt on the asset_tracker example of ncs v1.2, modified the following, and the interrupt didn't work: Where is available should be modified.
I set...
Dear Friend，
Based on nRF52832, mesh3.1, port ble dfu to mesh project, Android dfu application is based 'no.nordicsemi.android:dfu:1.10.1'; Call the following program: ...
My setup: custom board using nRF52840, Segger Embedded Studio 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4
I used a couple of your projects as a starting point for my code. Specifically...
Hi,
In my proejct, I am using WFE(); in some while loops because of core low power mode.
For example, waiting for time_out flags like codes below.
I am wondering if...
Hi All,
I'm new to the nordic product. We previous using TIcc2642 as development board. And we would like to test our application over different hardware. Is there any...
Im using CUstom BLE tutorial example and it works fine. But i just wanted to know, in which section is the text data for logging occuring. Ex: "notfication received from ...
Hi community !
I want to know if a code works on nRF52840 DK PCA10056 will work on nRF52840 PCA10059 ? On both, i will never use physical input (button led or gpio) i'm...
Hello expert,
I just jump from TI. Could anyone tell me if nordic has any chipset like TI CC1310 which supports direct access to the receiver I/Q quadrature samples?
...
The Thingy91 GPS system sensitivity is terrible. Getting the GPS to lock on takes forever, and many times doesn't lock on at all, and if it does lock loses the connection...
Hi community ! Here : https://devzone.nordicsemi.com/f/nordic-q-a/62414/different-behaviour-with-same-program-and-boards i get some problem with different behaviour when programming...
I'm using the Laird Connectivity BL654-DVK board as a basis for evaluating the nRF52840 for our application.
I started by using the .../examples/ble_peripheral/ble_app_hrs_freertos...
