Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi, I'm using nRF52 DK to develop and PPK v1.1.1 with Power Profiler app on nRF Connect v3.3.1 to measure current.
1. I see a lot of posts referencing the firmware on the...
Hello.
I have a issue about missing NRF_DRV_SAADC_EVT_DONE event in saadc handler.
setup is 52832, SDK 15.3.0, S332. enable ANT, BLE
for battery, sensor, I use 2 adc...
When I run the BLE peripheral HRS example on the eval board and try to connect with a Samsung XCover3 using the "nRF Connect" app, I got the error 22 (0x16): GATT_CONN_TERMINATE_LOCAL_HOST...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
Howdy,
I am using NRF5 SDK v15.0.0 on an nRF52810 custom PCB and am having a problem where the specified event handler is not being called upon completion of an SPIM transfer...
After unpacking I followed the first step at nordicsemi.com/thingy91, which is to update the firmware. I followed the linked instructions to update the modem and application...
Hi,
I have few questiones to initiate developing our project taking BLE Examples and BLE Services as reference.
Now,First thing we have to do in examples is turn bluetooth...
nRF Connect v3.2.0 - LTE Link Monitor is running on Ubuntu 16.04, and nrf9160 fw is v1.0.1. When connecting the board to my laptop, all Modem, UICC, LTE, PDN are Green. But...
hello
i am working with nrf52832
my code is based on the Ble blinky example from centeral. i added to the code with ble, uart, saadc and pwm and it was working great ...
Hi,
Using nRFConnect for desktop I've noticed that when writing an attribute I usually enter the hex values of a byte array (e.g. "12" = 0x12) but on other occasions the...
Hi Nordic Team,
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Can NRF52832 wakeup via any general-purpose pin?
- Is there...
Hello My ap plic ation is based on your bootloader (secure_bootloader_uart_mbr_pca10056) and your example "ble_thread_dyn_mtd_coap_cli".
When I send a special command...
Hello everyone!
I just got a Thingy: 91 and followed the startup guide, updated the firmware, and installed the modem...
I had trouble using iBasis eSIM because there...
My question is how to handle large amounts of data over the Gatt service
Our Current setup is 10 devices all on a Mesh Network. We use nRF5 SDK for Mesh and NRF mesh BLE...
