Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi, Nordic Team:
I am working with nrf52840 chip now,I want to use VDD output 3.3v. I have read the UICR Config Example and it's work fine when i use Keil to comp & download...
Hi, I'm working with the nRF52840-DK and need to be able to receive (slave) and generate (master) data on the same I2C lines. I'm aware this target doesn't support multi-master...
When selected, the link for the Linux installer downloads a .dmg file (same one as is downloaded when selecting macOS -- nrfconnect310.dmg). I'm unable to find another way...
Hello,
I am developing a device that will reconnect to an apple iPad if it looses connection and be able to send a couple of bits over ble_UART.
I have tried merging...
I see this error when transmission starts and after this RX simply do not work. Even clearing error not helping. Rx works fine when there is not any transfer done (firmware...
My environment: Keil 5; nRF52832 SDK 15.2 ; Softdevice S132 6.1.0
The uart bootloader code locate in the address: 0x70000 - 0x80000 ; (The MBR in 0x70000)
The application...
Hi,
I want to read and write MAX30100's registers. How can i do that? I tried a lot of solutions but I didn't solve that.
For example; MAX30100's address is 0x57. And...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
So, in my previous post ( https://devzone.nordicsemi.com/f/nordic...
I am using the nRF 15.2 SDK for Thread and Zigbee. I am currently trying to use the debugger in SES, but when I upload the code, SES complains that it can't find the source...
Hi
my devices use USB HID to PC now, and I have PC GUI.
I want use BLE send My device data to PC ( windows 10 )
if I use BLE HID services to PC
I need to do any...
Hi;
I am trying to add uart central to multilink central examble. I added some of uart part to multilink. i am trying to link two peripheral to central. when two peripheral...
Hello Nordic, for my project work i am using nrf52840 dk. with segger embeded studio i drag and drop the s140 softdevice hex file into the J-Link (chip PCA10056). and i tried...
Hello,
we are using the Nordic nRF52832, and I was hoping to update to the new SoftDevice S113 v7.0.0 as it seems like a better fit for our use cases than S132.
However...
My flash_placement.xml file is here and I am getting this error `.bootloaderSettings' will not fit in region `UNPLACED_SECTIONS'.`UNPLACED_SECTIONS' overflowed by 1024 bytes...