hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I made a Windows application that makes USB connection with nRF52840. You need nordic_cdc_acm driver to use it with windows 7. Can I distribute the nordic_cdc_acm driver with...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
I am trying to implement a struct that will be saved in non-volatile memory. Does the dev kit have these capabilities on its own? If it does is there a guide on how to use...
Hello,
I am using secure dfu with bonds (SDKv15.3, Segger, nrF52832), it works fine however after each dfu (application only) I lose the bond information.
I have search...
I am trying to communicate with PN7150 from nRF52840 DK using I2C pins.
PN7150 needs 3.3V and nRF52840 is supplying 2.9V.
I am able to read PN7150 on Arduino Mega but...
I made a Windows application that makes USB connection with nRF52840. You need the nordic_cdc_acm driver to use it with windows7. May I distribute the nordic_cdc_acm driver...
Hi Nordic,
We're developing a product based on the nRF52810 and got the following question:
We were wondering if we can recover a board in the worst-case scenario where...
Dear all, My team want to develop a innovative product. I am following this tutorial ( www.youtube.com/watch to enable the CMSIS Configuration Wizard in Segger Embedded Studio...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
Modem firmware version 1.0.0
Segger version v4.18
nrf tag v1.0.0
Often when I try to flash a new build of an application and try to flash an application through Targert...
Dear Team,
I want to integrate an nRF chip into my Project. I will use a ready made module from Laird, the BL652-Sx.
For Debugging I want use the nRF52 DK and connect...
Hi all,
we would like to add usb-cdc support for our nrf mesh project. I have tried merging an usbd example project into our application but without success so far. I am...
When I try parse string on nrf52832 with SEGGER Embedded Studio for ARM 4.16, I have a problem about "sscanf" :
Here is code:
It should output:
Num: 12
Num:...
Hello to all! I use the sleep mode PWRDWN = 0x04 and periodically wake up at WDT.With that, I see needles for the current consumption in the circuit to wake up the circuit...
I measured the output power over all the channel, see graphics below. It is not much, but i still would like to know why the output power drifts over frequency. Is this by...
