I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Greetings to all, I am trying to debug the PrnRF Connect Programmer with visual studio code, but I can not find a way to achieve this. They could give me a hint of how to...
we have a linux gateway with an nrf52832 connected via serial port. the gateway communicates with a modified connectivity HCI application on the nrf52. the gateway device...
Hello everyone,
I am using nrf24l01p. It works fine but some times gets hang, doesn't receive data at all. I am sure that this is not the problem of micro controller because...
I am using the original board. Crystal of 32kHz has not been mounted on this. So, I want to use the internal RC Oscillator. In addition, I use a hrs example of nRF5_SDK_11...
From the product spec, I can operate in either low power mode or constant latency mode. It is not clear how much (or what mechanism) compromises the latency when low power...
Hello,
I'm developing an application that is sending data every certain seconds in a mesh network and, in order to reduce the power consumption, I wish the node enter...
i am using latest version mesh sdk 3.1 .. i want to interface two boards and want to check the bidirectional using text message, example if client sending the hello message...
Hi,
How can I Understand why the nRF9160 is disconnecting from the network?
How can I read the modem trace bin file to understand whats going on with the modem ?
Hello,
Do you have a soft device that integrates both Bluetooth and USB on the nRF52840 ?
I want to program a firmware that uses both and I'm wondering if you have ready...
What changes are needed in SDK V15 sdk_config.h so nRF52832 can run on internal RC oscillator?
I am using the BLE UART example, nRF52832 with Soft device s132_nrf52_6.0...
I want to extend the list of known UUIDs with some custom definitions but I am unable to open the Open UUID definitions file.
I tried following the Adding UUID definitions...
When connected with RTT viewer, a pin reset with nrfjprog shows a J-Link Error popup saying:
J-Link currently uses target interface SWD while current debugger tries to select...
Hi!
I want to send heartbeat messages from 30 servers to 1 client/provisioner.
I can send _HEARTBEAT_PUBLICATION_SET to every server like OpCode = _HEARTBEAT_PUBLICATION_SET...
Hi，
I have searched the posts about how to send/receive more than 255 bytes ,SPI master EasyDMA mode , but still can not find the solution.
I want to know if a ArrayList...
Hi,
i am facing two issue in nRF9160 cellular application.
1.Asset tracker Application:
i loaded Asset tracker example firmware in nRF9160 eval. board. when i run this...
