I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
I am using 2 gpio interrupts from 2 separate sensors with active soft device. one sensor generates interrupts at around 400-800 ms and the other comparatively lesser...
Hi,
So I am trying to poll the signal strength of the nRF9160 DK and at first everything seems okay, the device gains connection and all the boxes in the LTE Link Monitor...
We have added Nordic Uart Service (NUS) into the nRF mesh code and we created two mobile application.
First mobile application:
- is for nRF mesh provisioning which is...
Hi,
The datasheet for the antenna used in the dev kit, P822601, has its specification performance measured on a PCB DUT at 140 x 50 mm^2 - which seems rather unnecessary...
HI !
i have a problem during importing nrf9160 project in SES , knowing that i imported this project and others with same toolchain installed and other requirement.
onetime...
hi all
i have been working on a raspberry pi hat design and i would like feedback on it's design
this is the link to the github repo and i do update it regularly https...
hi,everyone
I want to run the DFU example in meshV3.1.0 . but i still can't understader how to run it . below is my understanding:
1.ther are must have 2 devices , A device...
Hey, i having problems with uploading code to my Thingy52.
Equipment that i using: nRF DK https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK Nordic...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
Hi,
I am currently trying to test the capability of bluetooth 5 long range mode using a pair of SparkFun Pro nRF52840. I have used the blue-app-uart example and:
1)...
Hey
I am working on Bluetooth mesh. I am able to find the RSSI from server whenever i received the message from client in mesh(light switch example). Now I have to find...
We used NRF52832 to make a Bluetooth solution, but the customer wants the broadcast name of the product to be regular, and the MAC address also needs to follow a certain rule...
Hi
I have below requirement on NFC using SDK 12.3.0 and soft device S132. please suggest how to start with the same.
1.NFC operation. (Simple Read Write into NFC Tag Memory...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
