I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I have been doing some testing around DFU and I have noticed something strange.
My application size (according to nRF Connect memory read) is about 78 kB. (Left Image...
Hello,everyone,
I have successfully installed nrfutil using pip install nrfutil, but when I type nrfutil in the terminal, it shows -bash: nrfutil: command not found, how...
Hi,
We were trying out the long range central and peripheral examples found in github with the nRF52840 DK boards but we are not getting the specified range(We did switch...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
Hi! I am trying to read the voltage of a LiPo battery as explained in this blog post. The code on github however, is not compatible with the latest SDK for the SOC (12.3)...
Hey guys,
we are currently evaluating the pc-ble-driver-js. We want to get it running on a Raspberry Pi 3.
The Nordic nRF52840 module was flashed with SD Version 6.1.0...
Hi,
i am using nrf51822 interface with mpu9250 and i want to detect a tap without using of DMP feature of mpu motion sensor. my application requirement is low current consumption...
Hi,
sending some data from nRF52840 (DK or dongle) to a host computer via USB. When nRF52840 is connected to a "powerfull" host, all goes ok; when connecting to a "less...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
hello,
Now i transplant pwm_library programming to ble_app_uart_c(central) in SDK15.0.
But i found the program cann't run in NRF52 DK.
I found it build no errors but...
Hello,
We are evaluating now a new project and I am struggling to get a feeling about one moment of Thread network and its particular implementation with nRF52840.
In...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
