I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi. I have two codebases here:
A peripheral application on an nRF51822 using SDK 12.2.0, SD 130. It has two vendor-specific services: the Nordic UART service and...
Dear helper.
Currently, in my custom board had a GPS chip that connect to nRF52832 with UART port.
But also the only way that I can trace the log is the other UART port...
Hi
I have custom board with nrf52832. I have lion batery and 3.3V ldo for powering device. I attached shematic.
For preventing lion battery decreasing below 3V, i used...
We're thinking about implementing a machine learning algorithm in our nrf52832 based product. Before starting implementation, I would like to estimate the power consumption...
Hi.
I would like to route the BLE SPI signals to an external connector for use with external debugger.
Please specify which the nRf52832 pins are by default assigns to...
Dear Nordic Support Team,
I want to integrate ble_app_uart_c and ble_app_multilink_central into a nRF52840 as an edge gateway, and the nRF52840 node communicates to the...
I try flash read, write and erase with flash_fstorage_example sdk 15 on nrf52 dk
On main.c i can write and read with nrf_fstorage functions.
When i try nrf_fstorage_erase...
I try to use SDK15/FreeRTOS project.
I measured current comsumption on IDLE state(not run any task).
It's take about 200uA.
On FreeRTOS's portable/CMSIS/nrf52/port_cmsis_systick...
Hello there,
I purchased some NRF52832 Development Kits and some NRF52832 Standalones. I wrote some code and flashed it to the development kit and it worked. Otherwise,...
Hi all!
I'm using the fanstel board. I can see that the "ble - uart" examples run ok.
In the code the configuration assign to P06 (Tx) and P08 (Rx) , when i look in the...
I'm implementing an application which uses the Secure bootloader with bonds. What happens if I create a bond to a device in application mode and then switch to bootloader...
We are designing a circuit that will be supplied from lipo battery, vddh. I am wondering how decoupling capacitors on vdd will impact as it is suggested (in errata 202) to...
We are using pc-ble-driver-py on our Ubuntu host machine which is connected to the nrf52832 running connectivity firmware and we are able to run the examples, how could we...
Hello,
I have got a quick question regarding a potential workaround-setting for the BLE_HCI_DIFFERENT_TRANSACTION_COLLISION-error.
Here is what I am currently seeing:...
Here i am attaching the my working code of the application.in my application i am using the two peripherals one is TWI and onther one is UART.i interface some sensors with...
