the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
Hello,
I was just wondering what are the steps to download my software that I made to nRF51422 to the nRF51822. I changed the target device and the memory areas in the...
Hi,
I am using SD 120 9.1.0 and SDK 8 as a central and SD 110 V8.0.0 and SDK 8 as a peripheral.
I have a setup central connects with 8 peripherals. First I had 1 central...
Hi guys,
I'm wondering what is written there in "empty section" between 0x7c0 and 0x1000 address? Are there any special registers (which must not be overwritten)? It looks...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello everyone,
I want to know if it is possible and how to show advertising data on display lcd (20x4 or graphic lcd). I'm using PCA10028 board with S120 and Nokia5110 LCD...
Hello,
I have read through the pstorage documentation here: devzone.nordicsemi.com/.../a00018.html
and I followed the tutorial here:
devzone.nordicsemi.com/.../
...
I created a bsp folder dfu_dual_bank_serial_s120 from PCA10028/dfu_dual_bak_serial_s13 in examples/dfu/bootloader/PCA10028.
This is for supporting DFU over UART for our...
I am using a development board PCA10040 with an nRF52832
I am running one of the examples: gpiote_pca10040
Everything is working fine with this line in the original...
