Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I am trying to connect an MX25R6435F NOR flash on a custom PCB to an nRF52832 running nRF Connect SDK v2.8.0 using SPI. I am currently using the devkit devicetree with some...
Hi. I'm trying to flash the Cell Fund Lesson 4, Exercise 1 app – Reading buttons and controlling LEDs over MQTT, to an Icarus IoT Board v2 using the Actinius I/O Serial Programmer...
Hye,
using the nrf 2.4.2 toolchain
i have an unsolvable problem about ble on a nrf52840 based project with imu, i2s strip led, buttons, spi speaker...
i have a classic...
Hello,
We are looking at using the DTM sample firmware for BLE tuning in a form-factor version of our product. Unfortunately, the only GPIO pins we have exposed are SWDIO...
I am using the nRF7002DK development board, which features an nRF5340 as the Host MCU for the nRF7002 chip. I am testing the " Wi-Fi TWT Sample " sample project, which allows...
I have designed a PCB using the nRF52840 microcontroller and the MAX30001g ECG sensor. The sensor requires a 32.768 kHz clock signal via its FCLK pin, as shown in the attached...
I believe I have discovered a bug in the SLM firmware. I am using SDK v2.6.1.
When running the nRF9160 in MQTT datamode, we are encountering an issue where the slm_quit_string...
I have successfully setup my nRF51822 chip with Wireshark to capture BLE packets, using the 4.0.0 release of the nRF Sniffer software (extcap folder). However, the capture...
Hi,
I am currently using nRF Connect SDK v2.5.3 and want to update to a newer version, because I want to create a board definition and I want to do it in HWMv2.
Even though...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
nrf5340+nrf7002 running Zephyr with NCS v2.6.x.
When trying to connect to a wifi AP with incorrect credentials, I have several issues:
1/ the result of the (failed) connect...
Hello, After doing several things on my Ubuntu 24 host (I don't what might cause problem): -> Updating java OpenJDK to 17 -> running apt update & upgrade -> modifying my script...
I am encountering warnings while attempting to send Bluetooth notifications in my Zephyr-based project. The warnings are preventing successful notification of ECG data. Below...
HI ALL,
I am using v2.8.0, NRF54L15,and peripheral_uart demo has not made any modifications except for adding the following content. The test shows that the OTA upgrade...
