I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi Nordic team
Q1. According to nrf Connect SDK documentation, Zigbee and Matter samples all supported FOTA (firmware update). Where can I find the DFU samples for Zigbee...
Hi，
When the friendship node has established with the LPN node, how to verify that the friendship sends a useful message to the LPN node?Has it any API to verify the message...
Hi If I permanently see 3.3v even when the application is not running does that mean it is busted? I also see a lot of spikes in the output I have placed an order for another...
Hi.
I have a problem using dfu bootloader.
SDK : 17.1.0
SD : 7.2.0
device : nrf52840
dfu code : secure bootloader pca10056_s140_ble
uECC : 13.0.0
I implemented...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I need to detect and monitor...
Hi,
I am using a Raytac MDBT50Q module on a custom board of mine. I have no 32kHz installed (which is available inside the module), VDD and VDDH are common and powering...
I'm porting code from my device which uses the nRF52832 to the 840 DK. My general process was to get the code developed on my own device to run on an 832 DK, then an 840 DK...
Hello everyone, I'm new here, and new to using the Nordic boards. I have a question regarding the RF connector in the nRF52840_DK. I am trying to do some RF measurements with...
Dear Team,
We notice that systemOFF current varying from 220 nA to around 500 nA for different devices. For some devices we are able to achieve 300 nA as mentioned in the...
Hi,
I'am using the ble_uart example on a custom board, where I have the issue that the BLE advertising is only available after a reset OR when I comment out the uart_init...
Hello,
I would like to implement beacon feature with a periodic (each 10s) advertisement data update.
This is an extrapolation of my code:
Is there some function that...
Hello,
The part i am using is NRF52840 Rev 2 (Build Code Dx0)
How can i exact know what revision or build code the SOC has ?
I want to determine in application what...
I am using NRF5 SDK 17.1
SES
S112 for the nRf52805
I followed the guide for the 805
i then used the NUS Peripheral and was trying to setup the rtc so the device...
Hi,
I have a nRF52840 Preview Development Kit. I studied your manual, but I didn't quite understand if this is possible or not?
I would like to debug (therefore I...
