Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi, I am working on an IoT project that will use lwm2m, I developed an event manager architecture using the helloworld example base. Now that I am starting to develop the...
Hi,
Is it possible to check somehow if a BLE packet has been transferred (or not) from a peripheral to the central device?
Through a succesful transmission flag or something...
Hi, I'm using nrf52832 custom board and 14.2 SDK, S132.
In my program I'm using SAADC, PWM, I2C along with softdevice and PID. my device is working fine for some time but...
Hi! I've noticed that softdevice S113 is Bluetooth 5.1 compliant , and that the nrf52 family chips are Bluetooth 5.2 compatible in terms of hardware. a. Is there any target...
fds_init fails for several valid reasons, but my issue is how to recover. This for me was triggered by a firmware upgrade overwriting the fds file area. This can trigger fds_init...
Hi, I learned how to replace the softdevice for a normal application. I've replaced 140 with 340 in my app. However I don't know to do that for the boolloader.
What I want...
Hi Nordic,
I want to control an LED with the nrf GPIO, the LED Anode is connected to VDD, through a resistor, and the cathode is connected to the GPIO. Under this configuration...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
Hi,
Looking at the source code for nRF Connect SDK v1.7.0-677-ge3c356ec8 and SDK For Mesh 5.0.0 I can't find any indication that the following section of the Mesh Profile...
Dear Nordic,
we are devepoling FW based on nRF52832, SDK 17.0.2. We have 2 devices:
BLE Central with SD S332
BLE Peripheral with SD S112
We setted up an open BLE communication...
hi all,
i am using sdk v8. i want to on rtc when button is pressed and i want to off the rtc when it is released.
i am using bsp_handler only for button press.
PROBLEM...
