I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me. I'm using Eclipse IDE.
Im using a nRF52840-DK...
Hello,
I have recently switched my OS from FreeRTOS to embOS. I am now replacing the SDK files so my project will not be using FreeRTOS. I replaced the file app_timer_freertos...
hello,
I am trying to learn how to use the nrf52480 dongle and am trying to run the ble_connectivity example. I built it using Segger as is, no changes from the pca10059...
Hi!
I'm trying to sniff BLE advertising traffic using nRF Connect for Desktop on macOS and a nRF52840 Dongle.
I am running nRF Connect Desktop 3.8.0 on macOS Mojave 10...
I have done everything to install the VS code, installed Connect, Toolchains, SDK, Seggers etc. as in the help, but this is the result in VisualStudio Code:
It just keeps...
Hi,
The following code has been working fine since it was taken from the examples (NRF52840).
We wanted to remove the app_usbd_event_queue_process() so we enabled these...
Hello,
I have beacon advertiser and scanner. Scanner is scanning the devices from around. But its not scanning the device that i used for advertising. On the other side...
Dear Sir,
for my nRF52840 application made with the SDK v17.0.2 and S140 Softdevice I'm adding the peer module to a peripheral device example (UART with SAADC with timer...
I was trying to create my own sdk_config based on "$NRF_SDK/config/nrf52840/config/sdk_config.h".
I noticed it contains both the "NRFX" config and "Legacy" configs.
For...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
Hello,
I was trying to get a Thingy:91 to run asset_tracker_v2 with an external GPS antenna connected to the U.FL.
NCS 1.7.0.
Based on the Thingy:91, I was trying...
