Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
SDK: 15.3.0 Example: ble_app_multirole_lesc DeviceA: EYSHJNZWZ (nRF52832)
I want to know the relationship between API and events. Take "sd_ble_gattc_characteristics_discover...
Hi nRF Support,
I get nRF5 SDK version 17.0.2 and learn Peer Manager handler implementation (pm_handler_flash_clean function). Lets consider this case:
- 2 bonded peers...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available.
I did:
update the modem with mfwnrf9160123...
Hello, I am trying to program the peripheral uart sample on to my Thingy 91 using the nRF9160dk and 10 pin connector. I am able to successfully build and download the target...
I hope I am posting this in the right place but I am looking into learning more about developing devices that use Bluetooth. I have been looking into getting a dev board but...
Hello All,
I am working on nRF52840 DV-kit, using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71
I am trying to create .c and .h file in my project for gpio_configuration...
Hi,
I have layout a borad with nRF52810 and use IO to control other ICs.IOs map as blow.
#define LSM_6DS_SPI_CLK_PIN 9 /**< SPI */ #define LSM_6DS_SPI_CS_PIN 4 #define...
We are using nRF52840 chip for our development and till now we have used nRF SDK's zigbee CLI example for development.
Now we are interested in nRF5340 chip but I have not...
hi，
iI'm newer useing nRF5340， nRF5340 two cores communicate via IPC ,then exchange data through which path that is IPC or CTM ，What's the difference between IPC and CTM...
Hi,
I am powering the NRF52840 in normal mode by supplying 1.8v to VDD with VDDH and VDD shorted.
In order to use USB the VBUS pin is connected to the USB VBUS line. ...
Hi,
I am programming the PCA10040 board (tested 2 different boards) with the ram retention example program from the latest SDK (NR5 17.0.2). With this example is supposed...
Hi :
We create UART Over BLE service on NRF52832 SoC. It worked fine used SoftDevice V2.0.
Now update SoftDevice to V7.2.0. got this issue. where can i found SoftDevice...
I'm trying to drive the RGB LED light on the Thingy:91. So far, I've not been successful. I was hoping that by listing the steps I perform I might be able to get some advice...
Hi,rotocol
In Nordic's Smart Remote 3, it is mentioned that IR transmitter is protocol agnostics while IR driver is Protocol specific. Is it possible to write a common IR...
Hi,
Is there any battery life calculations for NRF52 and NRF51 (Beacon)?
For example: if TX power of NRF52 is 0 dBm and it broadcast every 5 seconds ? Or with any other...
