I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hello, I am having an Assertion failure like this:
My nrf/ext/lib/bin/supl/CMakeLists.txt looks like this:
Line 9 is already changed to if(CONFIG_FPU), as per the...
What is the default data rate of Nordic BLE, and when is it set in the Thingy code? I can't find any reference in the code to what I assume would be NRF_RADIO->MODE!
Why ram and flash size in a board configuration in Zephyr OS for nRF5340PDK doesn't match with declared on your site? According to your product specification, application...
nRF52840DK devicetree describes both uart0 and uart1 explicitly in nrf52840dk_nrf52840.dts file: https://github.com/nrfconnect/sdk-zephyr/blob/v2.3.0-rc1-ncs1/boards/arm/nrf52840dk_nrf52840...
Hello,
NRF52832 - SDK16 - sd132 7.0.1
I have an issue with ble_db_discovery_start() that return NRF_ERROR_NO_MEM, when I followed the functions call I found the error...
Hi,
I started with the Blinky example and have added peer_manager to the project by referencing the hrs example. Everything is building, but on init() I am getting a hard...
I have two custom pcbs containing the nrf52832 chip with the EXACT same hardware and software.
When I program and run the old pcb,
The old pcb runs OK. It returns from...
I use SDK 15.3 and SD S340 v 6.1.1. Bootloader is designed to do custom update through GSM; code based on secure bootloader ble example from SDK. I have used code that previously...
Hi,
Greetings!
We are using following setup
nRF52832 DK
SDK16.0.0
Mesh SDK 4.0.0
Light Switch Server and Client
Here we would like to understand below things...
HI,
I set RTS,CTS to disconnect in the overlay file.
(Toolchain Manager.0.6.1/NCS1.3.0)
&uart0 { rts-pin = <0xFFFFFFFF>; cts-pin = <0xFFFFFFFF>;
};
warnings occur...
Below are the details of my setup configuration:
SDK Version: 11.0.0 (with changes corresponding to hardware)
Soft-device: s130_nrf51_2.0.0
Boot-loader: nrf51422_xxac_s130...
Hi, I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment SDK - nRF5_SDK_16.0.0_98a08e2 ,
IDE - Segger Embedded studio (windows 10 - 64 Bit)...
Hello! I gonna buy a NRF52-DK. The seller says the following about kit version :" Hello, original imported. The latest version of 2020. 2.1.0 version". Is it correct? I can...
Hi
In my application, I use nrf52811 to relay data to make the data go further. If data is sent from point A to point B, point B receives the data and then forwards to...
