I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I would like to know how to build the aws_iot example without network offloading to the modem. I need to make AWS connections through both the nRF9160’s LTE-M connection...
Hello Nordic team,
I'm developing firmware for a custom board based on the nRF54L15 , where the LEDs are connected to GPIOs on port 2 . These pins do not support hardware...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi, would like to understand what scenarios a clock stability better than +/-40ppm would be needed in a BLE setup.
i.e. channel sounding, and similar. I mean you can get...
Hello,
I plan to use uart1 for serial port development based on the binary protocol. I will receive bytes using the interrupt method. But when I send bytes (such as FAFBFC...
I have a custom board with nrf5340 and want to run the radio_test sample on it. I have been able to compile and run the sample using the uart serial terminal, but I'm not...
Hello everyone.
i want to configure the TX power of the NRF radio in BLE advertisement and connection of the NRF54L15 MCU. I am using the nrf Connect SDK version 2.7.0....
I am studying Lesson 6/wifi fund_1ess6uexer2 and I can run the provided code normally.
（academy.nordicsemi.com/.../） But I still want to control whether to send packets...
Problem - while working in a project where VSCode does not have visibility to the nRFConnect SDK folders, but where the project includes project-specific KConfig files, the...
Hi,
i am under Windows 11 using the latest VS code extension (2025.4.106).
How should i use https://docs.nordicsemi.com/bundle/nrf-connect-vscode/page/reference/settings...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
I followed the instructions in Lesson 9, Exercise 5 of the FOAT course. However, I am unable to complete the build process. I was wondering if I might have missed a step or...
Hi all,
I’m working on a Nordic-based BLE project (nRF52 + nRF Connect SDK 2.6.0) and evaluating the flutter-nRF-Connect-Device-Manager package for our upcoming Flutter...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
