I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi I am using the nRF51 DK and I successfully ran the ble_app_template program from examples\ble_peripheral in SDK v10. Using the nRF connect app I am able to do both read...
I have to connect a MIC working on PDM to nrf52 DK Board.For that, I have written the above code. But when I am testing I am not able to get the clock pulses at the defined...
Hi,
I am troubleshooting on a nRF52810 that fails to erase/program. The device has been working in our product with a application software, but now it will not program....
Hello,
I want to enable the scanning with name for the first scanning of the device and after connecting to that device its address will be saved. After disconnection with...
I'm interested in using the nrf9160 as a drop in replacement for my current modem and GPS, where a host mcu would use AT commands or something similar. Has anyone attempted...
Hello,
We want to capture image data which is coming on parallel port on nRF52840 dk. The camera sensor we are using is OV2640. The parallel port (8-bit) data is coming...
Hi,
I am getting error while trying to configure Mesh node. I am using Light switch server example and configure through nRF Mesh Application. Attached some screenshots...
I'm trying to test long range beacons with coded phy on the nrf52840 dongle, so I've set out to turn my nrf52840 DK into a beacon scanner that will spit out data over uart...
Hi Sir,
I am use NRF52832 BLE to UART function, it was working good.
I am refer ble_app_hids_keyboard_pca10040_s132-nrf52832_xxaa example project to add peer manager,...
Hello,
I am a newbie to the Nordic development ecosystem. Just purchased a nRF52840-DK board and followed the instructions here:
https://infocenter.nordicsemi.com/index...
Hello,
Is there a way I can run JVM on nrf51 or nrf52 series devices? I have been searching the forums and did not find any updates on the same.
Any OS like embedded linux...
Hi,
We are currently in development of an IoT solution using the nRF9160. We are doing a set of EMC tests to ensure electromagnetic compatibility of the device. The test...
Hello,
I am trying to transfer a signal sampled on AN0 (P0.02) at 16kHz via Bluetooth using an ATT MTU of 247 and a 2MBPS PHY speed. The basis project used is examples ...
