I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I'm trying to implement the Gazell protocol for one of my tasks. I understand there is CRC for the data sent from the device to the host. I cannot however find anywhere...
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
Hello,
Is there any development board like an Arduino mini for the nrF52840. It need to fit a in very small enclosure
Ideally, I would like to test/develop some sensors...
Hi,
I am working with hid keyboard example on my Windows machine.
Problem 1 : After flashing the code, I make bluetooth connection and the code works properly. Then I...
Hi,
I am reading the Product Specification v1.3 of the nRF52832 SoC.
On page 23 the RAM0 block section 1 address is given as 0x21001000.
From the context I believe, this...
As per one of my discussions with , on another thread here , I can send a GenericOnOffGet from my android activity and I will get the status of the light in GenericOnOffStatus...
Again!!! I have a lot of problems to navigate on the Nordic products.
I follow the links and went to the start52840dongle and downloaded the SDK.
I find only stuff regarding...
Hi,
In looking down the road for product enhancements and migration to the 5.0 Bluetooth specification. I am interested and wondering if any discussion about chipset production...
Hi there,
one quick one:
when configured as SYSTEM RESET, Does P0.18 acts as an Input/Output? i.e. will be asserted Low by the NRF52840 while the MCU is in reset?
...
Hi all,
I'm using ble_app_multirole_lesc example to develop my application, it connect to android phone as peripheral role and now I need it to connect to another nrf52832...
If I have the J-Link RTT Viewer open and connected to my PCA10056 (viewing RTT output from an external board connected to P19) and then reprogram the board using nrfjprog...
Hello,
I am currently running into an issue with nrf51822. I am trying to write in flash a flag which defines the device I use. Indeeed, the device on which the code will...
