Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I want to add custom characteristic to NRF THINGY:52.
I am getting BLE_ERROR_INVALID_ATTR_HANDLE while I update the value to the characteristic.
Update is done...
Hi, I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using the latest version of SES and a J-Link Plus. SDK version 14.1.
I've modifed the CLI...
Hi Support Team,
I am trying to create the custom model - as far as I know there are two types of models possible in bluetooth 5 mesh - SIG defined and vendor specific...
Hello,
I have been playing with sdk 14.0 examples for a while and I wanted to try the Nordic UART ble_app_uart using multiple files (ble init, advertising, sdh separate...
I am writing a combined beacon and mesh node using the mesh SDK v0.10.
When dsm_local_unicast_addresses_set() is called in mesh_evt_handler() , which can be found in nrf_mesh_node_config...
I've sifted through the examples given to me, and none of them seem to explain how to create your own service and add it to the stack. All of the services that are registered...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
I am using the ble_app_uart example as my base on a 52840 with sdk 14.1. I have commented out BLE_ADV_EVT_IDLE case in on_adv_evt() function and the BSP_EVENT_SLEEP case in...
Hi:
I download the google official example "android-BluetoothLeGatt" from github
In the original code, the SDK26 is used, but it can not find any BLE device.
If the...
hi, i'm newbee in BLE,now i have a trouble about advertising in NRF51822.
in my project,after BLE disconnect, I can't see BLE again that mean BLE can't advertising continuously...
