Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
The nRF54L15-CAAA reference designs currently show an 8 layer board which includes 2 GND layers that seem redundant and possibly unnecessary? Can someone confirm that the...
Hello,
I have working BLE peripheral_uart example based application using nRF52840 dongle with SDK v2.6.0.
I tried to upgrade SDK to v2.7.0/v2.8.0/v2.9.0.
v2.7.0 seems...
Hello,
I would like to know whether there was a way to get the name of the broadcast emitted with the sample bap_broadcast_source from a nRF5340, but directly from the...
Hi DevZone,
As mentioned in the title, the Welcome page and Application page won't show any selection for my project as following image shown.
My project is based on...
Hi,
I'd like to sample PDM at 48kHz, I'm using nRF52840 DK and nRF5 SDK.
I read a post ( devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate)...
I'm bringing up ble_app_hrs as an eclipse project using gcc.
I'm running into an error in app_util.h, line 67:
#define STATIC_ASSERT(EXPR) typedef char static_assert_failed...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
We have written a Flutter app, which uses the Flutter-nRF-Connect-Device-Manager package to perform firmware upgrades on bluetooth devices that the app bonds with.
If iOS...
