we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hello. I want to change the board configuration in nrf7002. "In the nrf7002dk_nrf5340_cpuapp.dts file &spi4 { status = "disabled"; }; An error occurs when spi4 is disabled...
Hello everyone,
My project consists on using the nPM1300 with ESP32-S3 on a custom board. I2C connection is pretty much validated, since I have already configured some...
I have an app where I'm using the AP and STA mode of the 7002. I'm running on a nrf5340.
*** Booting nRF Connect SDK v3.5.99-ncs1-1-1-g6dc48c918694 *** [00:00:12.620,269...
Hello,
I am new to Zephyr and I am trying to figure out the best way to set up a new project for a nRF91 modem. Ideally, the project should allow patching of the nRF Connect...
Dear All,
I am working on a project using the nRF52810 with the secure bootloader configuration from the Nordic SDK 17.0.2 . Specifically, we are using the example:
....
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
With the nRF52840 we used RSSISTART to start the sampling of the RSSI and got a RSSIEND event when we could read the RSSISAMPLE register.
The radio on the nRF54L doesn't...
Hello,
I am working with the Multi-Service sample on the 9161dk and also a custom 9151 board.
The multi-service sample compiled option works great but the samples, when...
Greetings.
Background:
We have a custom device, that uses the nRF9160 as a Modem, with Modem OS 1.3.4 and a sightly modified "Serial LTE Modem" FW. One of our Devices...
I'm trying to send simple packets using the radio peripheral.
In my test scenario I have the following conditions:
The HFXO is started and is running the whole time...
hi
the lengths of the this track is important?
if i decrease this length, how i can set antenna parameters?
another question: what is the R1 =0 ohm resistor and N...
I am using Fanstel evaluation board with BT805 attached.
I got an example project - ble to uart.
I was able to build the project with Segger V5.42 (any later verisons...
Dear all,
I tried this example regarding async SPI:
https://github.com/too1/ncs-spi-master-slave-example
I also wrote overlay for this example to work on nrf52840...
Hi, we have a custom nRF5340 based device. Has NISB and MCUBoot Enabled. It takes about 2.5 seconds to get into the application and BLE advertisement to start. Wanted to know...
