Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have worked with the nRF24L01+ for a couple of days now without getting it to work.
The setup of the chip is done as described below, without any luck of getting a communication...
I am trying to debug communication over SPI to some peripheral to the NRF51822.
I am using the soft device and the bluetooth capabilities, and start the bluetooth stack and...
Hi,
I have paired two 51822 watches on iOS 8 on iPhone 6 plus. I found that when two watches moved far away and move back to the phone. The phone will not connect to either...
Hi Nordic Devs,
For my project, I am looking for couple of tactile SPST (Single Pole Single Throw) switches like this one . Would appreciate any alternatives that are cost...
Hi!
I realize that the paint on this is still drying, but I'm wondering if anyone is seeing the following behavior?
I can run an program based on this API once. When...
I'm developing a custom solution using the nRF51822 CFAC. The nRF518-SDK version 6.1 does not explicitly claim support for the CFAC. Will there be issues using this SDK and...
In my plan I have a rf moudle NRF24l01 , this is not important, so , If you see in figure 1 we have radio masts that send waves in around. we can't accept this. my plan for...
I have a system where any two identical devices need to establish a communication between each other, without any prior knowledge of which is master and which is slave. Currently...
I have the 51822-DK. I was finally successful in uploading the Heart Rate Monitor example application to the chip with the S110 but now it looks like nothing happens. I downloaded...
Hi nordics.
I am trying to do s120 multilink_central example.
However, this example doesn't work well, and I cannot debug central example.
-Environment-
board...
Hello,
I am working on pca100028 and using s130 softdevice(SDK 6.1.0.0.). I am trying to see UART log on pc. But my code get stuck at the following while loop.
void simple_uart_put...
I am using ATmega32s to drive the nRF24L01+ chips and a low dropout 3.3v regulator (TI’s LP2950) to power the nRF from the five volt buss.
Both the transmitter and receiver...
We are seeing bonding issue between Nexus 6 and our 51822 based product. After inspecting the sniffer capture, we observe that the phone advertises its IO capabilities as...
I have an nrf51822 S110 based application that tries to discover the primary services on the GATT server at every connection of a central.
Unfortunately, the central does...
