I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello!
We are working on a custom PCB with nrf54l15 chip on nrf connect sdk version 3.2.0.
The I2C (TWIM) SCL line functions correctly, but the SDA line is not being driven...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
Hi，
During full-device testing, we observed that two devices encounter the MPSL ASSERT: 1, 1519 error after approximately one hour of operation, which causes the MCU to...
Hi Nordic,
On the NCS3.0.2+NRF54L15 platform, we intend to generate pulse widths by controlling P2.1 and P2.5 through timer+PPI. Originally, we planned to use PPI for operation...
Hello,
I have a problem with a tablet that i was planning on using (Xiaomi Pad Pro), my device (nrf25840 dk) is sending data in packets, 4000bytes per packet and its sending...
Hello,
I am working on a custom product based on the nRF9151. I am currently learning RF testing methodologies and setting up a verification plan.
I have read the HW...
Dear all,
I am trying to build bluetooth hci controller for Home Assistant.
I used official example for create usb bluetooth hci controller here:
~/ncs/v3.2.0/zephyr...
Using the options described in ncs documentation for one image pair updates (i.e. not multi-image DFU) appears to be broken in ncs 3.0 and later for upgrading the network...
Hi all,
I'm working with the nRF54L and encountering persistent SAADC issues after short deep sleep cycles.
Setup:
SAADC is configured in differential mode with oversampling...
Issue
When building the Blinky example for the NRF54LM20A with TFM and CONFIG_DEBUG=y the MCU will assert on boot.
When booting an assert is triggered in workspace/modules...
Hello,
I have been developing on a nRF9151DK v0.9.0 for a few weeks now. So far this board is great! However, I have been running some long duration tests recently and logging...
hello, We have a project that uses sound for distance measurement.
When I upgraded from NCSv3.0.0 to NCSv3.2.1, I encountered a problem where the i2s function stopped working...
Hello, I previously learned that the nRF54L15-DK only supports a single antenna for Bluetooth 6.0 channel ranging and lacks a multi-antenna design approach or official guidance...
Hi, We are almost ready with our first board around nRF54H20, only one issue is remaining. We have prepared a sample, that records PDM audio as PCM wave, and stream it over...
