After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Reference link: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-1-dfu-over-uart/ I have an nRF54L15...
Hello everyone,
I'm working on a design using an nRF SoC and have a question about the correct way to handle I2C pull-up resistors in a mixed-voltage system.
My Setup...
Dear Nordic Support Team,
I’m encountering an issue during debugging where the code consistently hangs at line 360 in nrf_sdm.h , specifically at the following call:
...
Hi,
We are working with nRF52832. Over requirement is we need to transfer the file over BLE. We are using UART service (nus) to transfer file over BLE we getting maximum...
Hello,
I am working with a thingy9160 to connect to an MQTT broker using TLS.
I have run into an issue where the MQTT connection is disconnected with error code #XMQTTEVT...
Hi,
I have a nrf52833 with MCUBoot and BLE, I am using NCS v3.0.1.
I need also a custom NVS partition to store user data, so i create a data_partition for this purpose...
Hello,
I'm trying to build a Zephyr module that manages some features for a specific board (an SDK for that board). In it, I would like to enable the IPC devices in the...
I am testing data transfer from a microcontroller to a host PC using USB CDC ACM on the nRF5340. Right after powering on the microcontroller, only the first packet takes longer...
hi support team,
do we have any samples on how to show radio statues to gpio? when radio is on, gpio is set to high, and radio is off, gpio is set to low.
waht i can think...
Hi everyone,
I'm in the middle of a project and am starting to run out of available GPIOs.
To save a pin, I was wondering if it's possible to use a single GPIO (for example...
As a detour to getting DFU working for my existing project, based on nRF54L15, it was suggested in a previous ticket that the issue might be with my custom board folder, and...
Hello,
I would like to ask if it is possible to print the status of individual parts of memory on nRF7002-DK while the program is running? So far, I have managed to print...
I am using ncs to develop for NRF54L15. It runs fine on the development kit DK, but it doesn't work properly on my own hardware board. My program always fails to simulate...
Good morning,
I have tried to do the exercise 6 from the nrf-connect-sdk-intermediate course, my nRF9160 devKit can connect to nRF Cloud and download the new firmware. When...
