I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I am trying to receive packets from a device with Zigbee custom profile. Through sniffer, I can see that the device joins the network and sends packets on it but I cannot...
Our board doesn't have LFXO, but I want to run DTM. When I try to switch to LFRC by changing sdk_config.h, it doesn't take effect.
chip: nRF52832
SDK: nRF5_SDK_17.0.2...
Hi, we use the Fanstel BT40 design a RS232 & USB carrier board, when we use battery 3.3V to VDD, there is a DC2.8V output from VDDH. VDDH should be power input, why there...
As known in SDK nrf there is a function battery_level_in_percent() used to calculate battery percentage but it is only true for the CR2032 battery. Currently, I am using AAA...
My application uses a SPI LED driver, which I routed on a PCB to the most convenient pins for routing.
I have already tested my firmware on a nRF52833 DK with an Arduino...
Hello, I'm a beginner at developping nrF52832. My problem is completely similar to this one : devzone.nordicsemi.com/.../add-saadc-peripheral-and-others-to-example-project...
I am trying to measure single-phase mains voltage (240v, 50Hz) by stepping down the voltage to 200mv using a voltage divider and read it with the ADC pin of the controller...
Using NB- IOT JIO SIM in india, not connecting asset tracker Work Up to RRC Connected and stuck there. This is custom code very similar to asset tracker example. We are using...
Dear Sir.
Using the mqtt_simple project , I inserted a 1 sec timer.
Within the timer I want to use the publish routine like this
data_publish(&client,MQTT_QOS_1_AT_LEAST_ONCE...
Hello everyone, we are developing a heart hare accessory for the phone and we want to show the battery status directly on the phone. I found it can show up in the Windows...
Hi, I run nRF5 SDK 15.3.0 with SES 4.30c on a PCA10040. Yesterday I upgraded to nRF5 SDK 17.0.2 and SES 5.60. When I connected PCA10040 I got a message that something wanted...
Hi everyone,
I write a firmware to read the values from a 6-axis IMU and some force sensors. I want to sample with a frequency of 100-200Hz, to store the data in a buffer...
Hello,
I have already a Thingy:91 running and sending me data over MQTT using the mqtt_simple Sample.
Now I wantet do change the broker to one with credentials but unfortunately...
