After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
I'd need some information I'm not able to find in product specification v1.3:
What is the architecture of the GPIO / AN pins of this device? Input p rotection diodes...
Hello,
I have successfully programmed the ble_app_uart example to a custom PCB using the 52832. Here is the board schematic, on the board C15 and C16 are not fitted.
...
Hi,
I want to know is Liniux system supported Nordic BLE OTA DFU ? According to official documents： https://www.nordicsemi.com/Products/Development-tools/nRF-Util ，it just...
Hello community,
I am implementing BLE peripheral code contains, A custom service, characteristic.
I am referring this link : github.com/.../custom_ble_service_example...
Hello, nrf5340 datasheet -> nRF5340_OPS_v0.5
section: 7.1.26.7 Sending custom instructions (Page: 383) 1. we can send an instruction consisting of a one-byte opcode and...
I kind off trying enable TWI in bootloader mode, This is because of following reasons.
Firmware is stuck in bootloader, if somebody removes the Device Battery during...
Hi.
I'm trying to run an application using a custom SPM module in a nRF5340 where I get an error while running it. I'm using nRF Connect SDK. The terminal gives me this...
Hi
I have searched this question on the website before posting this and found that the nRF52 devices support SWD interface (which is peer to peer) and not JTAG (which...
Hello,
I was able to install all tools proposed by the nRF Connect v3.7.0 except the most important : Toolchain manager.
It retruns the following message
running...
Hi, I am interested in using the KMU and I have seen some examples of it here (9160 but similar): https://github.com/einarthorsrud/kmu_sample
and also some docmentation...
Aim: To upgrade the existing Bootloader + Softdeivce + Application package build using nrf_sdk_15 to nrf_sdk_17 on the NRF52840_DK.
Problem: I successfully flashed the secure...
We are using zephyr on that nrf52840 .
Is possible tu run code coverage analisys on that board ? What I have to do ?
Does twister work ?
Best Regards
Novelo G
