Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
Hello
While converting from nRF52832 to nRF52810, we found a problem that the SEGGER compiler returns with the message
section '.init' will not fit in region 'UNPLACED_SECTIONS...
Bluetooth didn't have a standard for transmitting audio using LE until LE Audio was released. And many manufacturers which produced BLE remote controls used Voice Over HID...
In my project, nrf9160 has to send and receive data from the I2C bus from a chip. Everything works fine but unfortunately I have to query the chip by sending a single byte...
Hi,
I'm using nRF52840 DK to construct and test a wireless data transmission system.
The problem is that I need to detect a 2M Hz clock's rising edge using nRF and...
Dear Community,
we are looking into an application where the Gateway (RX) uses the nRF5340 + antenna array and the clients (TX) the nRF52840. The clients are on the market...
Hi, we are trying to characterize RSSI and TX output power with nRF52-DK board.
We used a nRF52-DK (TX) and 2.4-GHz BLE antenna (chip-type, RX) was connected to spectrum...
Dear Nordic Team,
After updating the modem firmware to the latest available (mfw_nrf9160_1.3.0), my device LED does not come up anymore. Additionally, I can longer see my...
Hello, I am trying to use open-thread with NRF52840. There are two different SDK one of them is NRF-SDK for Thread and Zigbee and other one NRF-Connect. Nordic recommends...
Hi
I was wondering if using sd_ble_gap_rssi_start to measure RSSI value during connection has any influence on power usage or ble data throughput (or other resources). Or...
Is there any way to programatically set the 51822 into debug mode following a power on reset, or disable pin reset in normal mode?
Here is a synopsis of the issue:
...
For my project in development I need to read characteristics from BLE devices using pc-ble-driver library.
I am using a C program, not python bindings.
The method I am...
Hello, I am using Nrf52832 and want to run client and sever simultaneously. I think it's possible but unable to find the sample code. Can you please help?
Thanks
