I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I’m working on DFU using the BLE Mesh distributor and target sample codes. I built both with Sysbuild and flashed them onto two separate nRF52840 boards. The target board...
Hai,
We are developing a product having nrf54l05. I'm using nrf connect sdk for programming. I'm using one GPIOs for input. I have enabled pullup for that pin. We want to...
1. development environment:
software ncs3.0.1 , DW3xxx_XR6.0C_24Feb2022, vscode
hardware: nrf52840, DW3210
DW3210 is a UWB chip produced by Qorvo, and its corresponding...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
hi support team,
i have close this ticket:
but i need open this ticket and ask how to program 9151 externa; spi flash.
i don't know if 9151 json file is correct and...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
This is our first time using TC2050 for the smaller footprint in our prototype. But we can't establish a connection with JTAG in nRG Programmer.
Below is the log from...
SDK: NCS 3.0.2
Part: NRF52840
I am running the NRF52840 as an HCI controller over SPI. I can advertise and connect. However, I need to advertise while connected and support...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Background
I'm working on a BLE application for the nRF52811 and facing significant flash memory constraints when trying to implement OTA/DFU functionality.
From my understanding...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
