Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I'm using the NRF9160DK, the asset_tracker example works fine over Cat-M together with the iBasis sim.
I want to run my applications on NB-IoT, so I'm trying to connect...
Hi,
I have an issue of watchdog in my application.
I think it may occur due to an interrupt (NFC trigger), which calls the function xTaskGetTickCount () instead of...
Hi community ! I saw a lot of subject about "Mesh throughput" which was outdated and i still have questions. I'm using nRF52840 DK with nRF5 SDK for Mesh v4.0.0
1) Does...
Hi,
I'm using nRF Connect to connect to the secure bootloader. In the debug log I see that an MTU of 185 is requested and 183 is replied. I also see this in the Wireshark...
When I used nrf52840 to connect the peripherals with pc-ble-driver-py, I had my own custom UUID, so I needed to add a custom UUID. I referred to this article , but the following...
Hi,
I know that there are different ways to set up the radio, but generally speaking, is there a general practice for how commercial devices' PHYs are set up when advertising...
Hello people, Honestly this is a problem more related to a Raspberry Pi than the nRF52832 but I'm getting same difficulties here so I will explain my situation. I have been...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
Our hardware has Winbond NAND Flash chip connected to the nordic MCU(nrf52840 /nrf5340). However QSPI cannot be used as nordicSDK doesn't support NAND Flash.
I understand...
Hello,
I am using the Power Profiler Kit connected on top of an NRF52840-DK
I am using IAR and using IAR's J-LINK plugin to program/debug an application on the DK. However...
