I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
This is in continuation to the previous question I asked which is linked here: https://devzone.nordicsemi.com/f/nordic-q-a/52575/making-a-ble-ibeacon-with-gap-gatt-profiles...
Hello,
I have used for my application the reference design of NRF52832.
The connector MURATA MM8130-2600 is used to have the choice between the PCB antenna and an external...
I have refer to this topic for setup multilink with NUS. https://devzone.nordicsemi.com/f/nordic-q-a/18804/mismatch-between-connection-handles-in-ble_nus
But, i met a wrong...
Hi Nordic,
While testing USB CDC example with nRF 15.3.0 in PDK board, I see USB is not recognized. I have gone through the same issue posted in Forum. Is it the issue with...
I have a question about “BLE_HCI_CONN_INTERVAL_UNACCEPTABLE”.
SDK: 15.3.0 Example: ble_app_multirole_lesc (source changed from sample) Device: EYSHJNZWZ (nRF52832)
The...
This microcontroller is advertised as mbed enabled. Does that mean that it can be easily programmed using mbed api in an mbed environment. I want to work in a c++ environment...
I am trying to use the nRF52-Development kit with (N52832) and using nRF5_SDK_15.0.0. What my application is to broadcast an iBeacon Packet (with Major, Minor, RSSI and UUID...
Hi,
I followed this tutorial ( https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/merging-two-ble-examples-together ) of combining UART example with other...
Hello. I use nrf52832 on Adafruit Feather board among with nrf5 SDK. As a default I can log any info via NRF_LOG_DEBUG to my serial monitor. But how can I use Serial input...
I was wondering if the standalone nRF51822 microcontroller has support for i2c. If so which pins are supported. There doesn't seem to be any reference on i2c for the board...
Hi,
I bought a custom nrf52840 board and I need to program my firmware on this SOC with PCA10056 DK debug output port. in below you can see part of shematic of my custom...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
Sir
about the
while(1)
{
sd_app_event_wait(); //stay here until a interrupt or connection occurs...
}
During the time that there is not a interrupt and no connections...
