Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello,
First, I follow this tutorial --> https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . It's working well on the...
Development Environment: Segger Embedded Studio 4.16
Debugger: Segger J-Link Lite/ Segger J-Link Pro
Debugging a custom nRF52810 board using SWD interface.
I am experiencing...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
I try to test Relay performance of BLE mesh, my setup as following:
1 one client loaded light switch client;
2 two server loaded light server with Relay On;
3 one sever...
Hi, I'm looking to use the nRF9160 DK as an IoT Bluetooth Gateway as listed on the nRF9160's product page. Basically, I am tasked with connecting two nRF52840's (both in GATT...
Hi, I am developping a product with battery power. To preserve the battery life, this product needs to work in low power mode. How can configure nRF51 to advert in low power...
Hi,
I'm using the PCA10056 as a JLINK to my custom board. My board is powered by a LiPo battery through VDDH, and I have access to the SWD pins. I'm also using Segger Embedded...
I started from the blinky example for pca10040e (NRF52810) on SDK15.3, added some files and code to get TWI_MNGR working but i get an error which i can't solve
`.nrf_queue...
Hello
I am currently trying to read data and save the timings of it. When pushing a button on my custom made PCB, the microcontroller goes to the handledata function....
Hey,
So I've been using the Verizon SIM card supplied by nordic with our nRF9160 dev kit. I never really new how the APN was getting configured because it just happened...
