I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi,
What are the reasons for the nRF connect app or the nRF Mesh app or even the nRF UART app to connect to an Android phone?
I can see the DK advertising. I can see the...
Hi,
I am using nRF52832, SDK 15. My code is based on the freeRTOS code examples.
I am trying to Run my Task Every 10 ms. I tried to test this by using a counter to print...
Hi,
I have a problem with soft device. My code build well but when i try to compile it on nrf52840, i have below error:
Then i tried to go in boot loader:
Therefore...
Hi, Everyone
I have a product (named "A") developed on sdk12.3 and 52832.
This product has peripheral function and MTU Size is 64.
If I use "nRF Toolbox -> UART" on my smartphone...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello
I am using Segger Embedded Studio with nrf9160. I can 'Build and Run' the 'asset_tracker' project but the LEDs are not blinking and my development kit is not connecting...
Is possible to get a sample code for communication between multiple BLE devices, for example the BLE TinyShield? I have come across a code that enables the BLE TinyShield...
The content, format, and size of a device's Peer Data is determined by the application. I understand that when pm_peer_data_store() and there is not enough available flash...
