I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi all,
I am using power profiler kit to measure as mentioned below screenshot.
I want to achieve current number as mentioned in Nordic product specification as" IOFF_RAMOFF_RESET...
Hi,
I'm using nRF52832 with IAR and SDK V15, S132.
I incorporated the peer manager in the uart serial profile example.
I assume, since I have 3 pages (inc. GC) set in...
I have a device that uses peer manager to pair using a key. I have noticed that the device will connect to an app and stay connected even if the pairing procedure is not completed...
Hello,
I am using the nRF51 dongle, SDK v10 and s310.
I want to use the dongle as a ANT+ receiver and BLE client to connect to multiple BLE peripherals. I have looked...
I am once again frustrated with nRF5 API's. Getting a value from analog input pin is that simple with Arduino API's:
int sensorValue = analogRead(A0);
That's all you...
I'm using an IMU sensor and transferring data over Bluetooth to Android device. The data sampling at 400hz, and I'm sending 6 packets per connection, each packet 20bytes....
Hello!
I am using the PORT event interupt sense handler to wake up the device from various pin interupts. We have in total 6 pins that need to do that.
This works fine...
Hi,
In my project, I am interfacing various modules (UART over ble, ADC, SPI, I2C) on nRF52840-Preview-DK board. I use IAR Embedded Workbench with nRF5_SDK_15.2 for code...
Need assistance/recommendations for working with smaller pin pitch (150 micron) mounting holes for the new nRF52480 chipset. Our current contract manufacturing supplier for...
Hello I noticed the problem with nRF51 DK and ble_uart app.
1. The nRF51 DK is connected to the Terminal
2. Connect to the nRF via "nRF Connect" application on Android...
Hello:
I read the documentation and errata for Rev 1 of the nrf52. I am using the Rigado BMD300 module (thus the nrf52) without a softdevice attempting to do on the fly...
Hi All,
Currently i am working on nrf51822 chip, For that i have downloaded nRF5_SDK_15.0.0_a53641a.
Now, i am trying to execute mouse hid example in nrf51822 chip, but...
Hello, it seems that the 15.2 infocenter radio_test instructions are somewhat different from the 15.0 infocenter instructions . Trying to get a general understanding of how...
Hi there,
I was hoping you guys could point me in the right direction with regards to the use of the nrf_mesh_disable() & nrf_mesh_enable() functions. Since the "friend...
I migrated my nRF52840 project to nRF5 SDK for Thread and Zigbee 2.0.0 (from 1.0.0), but I keep getting a linker error:
Building ‘myproject’ from solution ‘myproject’ in...
