I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am using SDK v2.5.0 on custom board.
The board has an external 4MB flash chip.
I am wondering though which paritition will be used for the update process, and how that...
My project: I am developing a system consisting of a central and up to 20 peripherals based on the Multi-NUS protocol. Toolchain and SDK : NCS v2.6.1. Development target:...
Hello,
I have a project for the nRF52811 using the nRF Connect SDK. As I understand, it’s not recommended to modify the main .dts file directly; instead, changes should...
Hi Team,
Problem: I'm working on a project using the nRF52840 and nRF Connect SDK 2.2.0. I need to transfer some files from host over UART and store them in LittleFS. I...
We are experiencing interruptions in the audio, with noise similar to popping sounds.
When observing the waveform on the spectrum analyzer during the audio interruptions...
Hello I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle It builds and runs just find on the nRF52840 DK But when I try to build for the dongle...
I made a custom board And I am running the segger example ble_app_blinky_pca10056_s140 But Even if I run log_init();, it returns error code 5 And even if I run timers_init...
Hi,
I have updated the device application firmware from nRF Connect SDK v2.6.1 to v2.7.0.
The firmware was working fine in v2.6.1 without issue. But the same firmware...
mcu: nrf5340
board: nrf5340dk_nrf5340_cpuapp
sdk: v2.6.1
When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
Hi, I have been trying to use my esp host mcu with nrf5340dk as a controller.I am using the hci_uart application with CONFIG_BT_LL_ACS_NRF53 =y to include le audio support...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
Hello,
I want to run mass storage on my custom board with the nRF52833 and W25Q512JVEIQ. I have reviewed the mass storage sample (ncs\v2.7.0\zephyr\samples\subsys\usb\mass...
