I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
I'm using an STA+AP configuration as well as monitor mode with a custom nrf7002 driver, which currently is working in a basic sense. I have however ran into issues regarding...
I got this chip from Raytac mdbt50q-1mv2 on a custom evaluation board , where i can access almost all the pins ( ~30/48 ). This chip came without any programs or bootloader...
Hi,
I am looking for a freelancer in a country, that has at least LTE-M for iBasis Sim cards to work on the following project.
I am building an asset tracker product...
I keep getting the following error when building this file: Pin 15 of &gpio0 already assigned to 2 other nodes
[{ "resource": "/C:/Users/User/zephyr/boards/arm/pinnacle_100_dvk...
I am trying to use second virtual interface of NRF7002 to use with custom linux driver. I intended to use it to add support of STA+AP or STA+STA mode. However, I observing...
Hi,
I am using nrf SDK -16.0 with board nrf52840. In Ble 5 we are using LE Coded PHY with S=8.
for Ble 5, the average current consumption got doubled when compared to...
This seems like it should be simple, but I cannot seem to set a custom static BlueTooth ID on an nRF52832 under PlatformIO / Zephyr - it just keeps generating a random ID...
Hello,
We are currently developing a Zephyr-based connectivity solution using the NRF5340 alongside an NRF7001 WiFi chip. Since we also want to use Bluetooth we have implemented...
Hi All, I'm working with MAX86916 sensor and trying to measure the FIFO/RED/IR/GREEN/BLUE data to measure SPO2, Heart Rate, Heart Beat but I'm not able to read any data on...
Hello,
I want to control LED of the Server 2. (Turn on / off) by using Client.
How to add the relay node in light switch example (this is one of the basic example...
I am trying to update a device using a Macbook pro with Sonoma 14.4 and am receiving an error message that states that nordic "Did not receive checksum response from DFU target...
hello, I'm using nrf52DK & connect sdk v2.6.1. I'm in the process of migrating from nrf5 SDK to connect SDK.
My previous code to read Mac address to form unique BLE names...
I am getting a warning in my nrf5340 overlay file because I ran out of pins and need to reassign P0.30 to my BMI270 interrupt 1. Here is the message in the overlay file: ...
I am using visual code studio, zephyr RTOS, v2.5.2 on NRF52840
I am trying to find a QSPI example
I noticed someone mentioned the sample :spi_flash is using QSPI ? But...
