Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I've updated my project from 2.7.0 to the latest (3.4.1), which was an experience. However, I've got it compiling now, but I'm getting the following error in the SW PWM driver...
Hi there,
I was going through Nordic Semiconductor's Introduction to Bluetooth Direction Finding video. In one slide of that, host talks about area of coverage of Antenna...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
NCS: 3.4.0 Chip: nRF54L15 Hello, in the past months, there has been quite a change regarding Security and Vulnerability Monitoring on the Nordic Semiconductors side. I got...
Our company is developing second-generation implantable medical devices and plans to use the nRF54LM20A chip/component. We place a high priority on product reliability, so...
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
Hello Nordic Support Team,
We are currently evaluating and developing custom application firmware on the nRF93M1 DK (Hardware v0.4.0) using nRF Connect for VS Code .
Issue...
Title: nRF54L15: Stopping WDT (WDT31) in PM state entry does not decrease sleep current (~2 µA)
Device: nRF54L15 NCS / Zephyr Version: ncs 3.4.0 and zephyr 4.4.0
Description...
Dear Nordic,
Currently nrf7002 dts binding file for QSPI bus has an 'QSPI' label inside for [compatible, on-bus] scheme matching, This may cause problem on non-NRF host...
Our firmware currently uses Zephyr test USB IDs: VID 0x2FE3 / PID 0x0100 (build shows warning about it). These IDs belong to Zephyr and only for testing.
USB is used only...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
Hello,
We are developing a product based on the nRF9151 and are preparing its CE/RED conformity assessment. We would like to leverage the existing nRF9151 CE/RED certification...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...