I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
HI there,
I wanted to use nrfx spi with nRF5 SDK 17.0, but it was removed. I checked that in nRF5 SDK 15.3 it should be available, but when I downloaded it the example is...
Hi Everyone,
Last two weeks I'm trying to make a Real time streaming custom service on PCA10056 DK. I have modified the ble_image_transfer code according to my requirement...
I'm testing the Zigbee CLI Agent example and try to read info from my Titan wall sensor. I can read almost all info, but not values, that are using float type.
How I can...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk-psm-current-too-high-after-opening-and-closing-a-tcp-socket/260026#260026 , however they said...
I have been looking at the Mesh library for BLE communication and wonder how much work it would be for me to use the same library for a long range 2,4 GHz radio?
Is the...
Hi,
now we use SDK17 "ble_app_hids_keyboard" example, we found after the moble phone connected to the ble keyboard, if the ble keyboard power off and power on ,the phone...
I am trying to to do adc reading from external 9V Litum battery.
In the PS document, I know nRF52832 can read adc until VDD(3.7V ???).
Then, in my case, do I have to design...
Hi,
I use the timestamp log in SDK17, and I find the time will auto clean at about 1min6-7sec.
Below is the code init the log.
/**********************************...
Hello,
I have a setup containing an NRF9160 communicating with another chip over UART at a 1M baudrate.
The following code is currently used:
I have configured the...
Hello team,
Greetings From Deepa. I need an manual installation procedure and building, compiling and Running the zephyr -OS with my laptop for learning purpose. I browsed...