I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
Hi everyone,
I am looking the TWI examples and I am confused regarding the nrf_drv_twi_tx and nrf_drv_twi_rx . What I've understand so far is that the nrf_drv_twi_tx function...
Hi,
We are developing the project based on nRF52840 chipset. We are configuring the chip for mesh application and using generic on/off model to send the data on the mesh...
Hello ,
There is two kind of clock source as i can see from the sdk files;
one of them is cpu that is ok but for the first one i couldn't figure out it's source "NRF_SYSTICK_CSR_CLKSOURCE_REF...
Hi all,
I've got some code running on my nRF9160dk that is behaving oddly. LED 3 blinks as expected (2 seconds on, 1 second off) but GPIO 10 (pin 18/ULTRASONIC_TRIG) remains...
Hi all, I'm a little blown away by the complexity of logging for this application (its highly likely I'm missing a few key elements to my understanding). I'm under the impression...
Hello, I read the instructions here for using the Nordic NRF Connect app for testing the CTS example: https://devzone.nordicsemi.com/f/nordic-q-a/53382/implementing-current...
Hello,
Hardware: nRF52840
SKD: nRF5_SDK_16.0.0
SoftDevice v7.0.1
I am working on creating a multilink central application where my central device connects to 3 peripherals...
Is there an issue with releasing application firmware, say v1.0 with and then in a following release via DFU, say v1.1 with .
I'm trying to understand if a network has been...
The nRF52832 (QFN package), Pin 44 is listed as "No connect" and has an additional description of "Leave unconnected". Question is what negative affect would occur if this...
Hi
I am unable to configure the nrf52840 dongle in client mode in light switch mesh example. I have changed the simple_hal.h to include the dongle board as /** Boards with...
I developed a software based on Blinky. I have been trying to add DFU to the current iOS app which is working properly to be like the Android app.
As I did in Android, the...
Hi, I would like to skip pairing process alltogether and just provide the KEys which were generated for both devices beforehand. My question is only. Is it possible to initate...
I have an application that will have up to 20 devices communicating with a gateway. Each device will need to send around 2MB of data every 5 minutes. We would like to use...
Hello.
I try to BLE and GPIOTE.
The reason for using GPIOTE is to read data from the temperature sensor.
And I want to sending data of temperature sensor by BLE...