Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I am working with the mesh 4.0 light switch example and had a general question regarding a custom model I created based off the simple on off model.
During configuration...
Hi,
Our application sometimes hits a breakpoint in SoftDevice at either address 0xA60 or (less often) 0xA80.
Based on this post https://devzone.nordicsemi.com/f/nordic...
My question is very similar to this .
I am posting again since it did not seem to be answered.
The error originates from the following:
This happens when I am trying...
IAR IDE can be used to develop and dug the code of nRF52832 . However , IAR IDE can not programme the flash of nRF52832 directly . I need a kind of flash programmer tool ...
Hi all,
I am working with Segger ES on chip nRF52832 with nRF SDK for Mesh v4.0.
I am stuck now at message publication.
I have discovered that my code runs to packet_send...
Hi,
I'm using the nRF52832 with FreeRTOS and SDK 14.2.0 . I took a look at Profiling the Softdevice and FreeRTOS with Segger SystemView and Instrumenting with Segger SystemView...
Hello,
I am using nRF5 SDK v16.0.0 on nRF5232 PCA10040 DK.
I am trying to create an application that will count the number of button presses (GPIOTE events) using a Timer...
Hi.
I'm using nRF52832.
There are some NC pins in my schematics.
How to control them to save current consumption?
Making them output and low is the best solution?
Hello,
Is it possible to configure the board as a peripheral device that provides the Nordic UART Service and allows multiple central devices to connect and exchange data...
Hi Technology, I use the Keil 4 version of the IDE, the chip is Nrf52832.Open examples-code appears this problem, how to solve?
Installation of NRF driver library package...
Hi,
I'm interested in using data signing for authentication since encryption is not wanted. However, I have not found any support for this. Currently I'm using softdevice...
Hi.
we setup a project according nfrconnect --getting started assistand,but it fail in seggerstudio,
we use sdk1.2.0(cd ncs/nrf • git checkout master • git pull • git...
I'm using fstorage to store logged data in Flash. Works well, no problems there.
What I'd like to be able to do though, and haven't found a solution to, is to be able to...
Dear,
I am working with THINGY91
ncs_1.2.0/Modem FW_1.1.1
SIMcard: Telia (LTE_M and NB-iot) / Horten.Vestfold.Norway
I am looking for information about AGPS, could...
HI,
Is there a minimized version of the relay example that shows how to transfer a message from device to device without the art of the HRS?
I hope it will be less than...
