NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
\nRF5_SDK_17.1.0_ddde560\examples\peripheral\pwm_driver\pca10040 In Demo1,i assigned the same pin to the 4 channels. I expect every cycle LED0 has the same behavior. But,...
Hi Networks,
I have tried to build the nRF5340 DK as a gateway.
Enabled
1. CONFIG_BT_GATEWAY=y
2. CONFIG_BT_GATEWAY_ADV=y
3. CONFIG_BT_GATEWAY_GATT=y
But not acting...
Hello,
I will be designing a board using with nRF52833 with the NRF21540 for the added gain. Would it be possible to add adaptive frequency hopping?
Thank you,
Shah...
The central device has the below settings
One central device A and two peripheral devices B and C, B and C have the exact same firmware. A can establish the connection...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
Hello,
I'm migrating my project from using child/parent to sysbuild ( simple Hello world code, and using MCUBOOT + NSIB ).
The first error i faced when moving to use sysbuild...
Using Zephyr.
I'm looking for a process or a function to log unconditional message in the logging system including timestamp and other typical logging/display functionality...
We have a custom board with an nRF9160 directly connected to a SIM-S-IO3-MFF2-2 IC. I understand these kinds of eSIMs in IOT devices are typically provisioned over-the-air...
I have a slightly off the wall requirement where I need to send a serial data stream at 5kbps, it will be used to drive an external OOK 433MHz transmitter. The data format...
Hi,
I am having some issues when trying to enable the Fast Pair when executing the bt_fast_pair_enable(). I used the debugger to determine where it's failing:
...
Hello,
I am working on setting up the nrf52 (nrf52832) to communicated with the AD4130 from Analog Devices via the SPI Port. However, I am encountering a problem that I...
Hi,
I'm using the nrf9160, sdk 2.4.0 and tool chain 2.6.1. I need to scan the i2c sensor, I didn't find the i2c scanner example. So i was add one code and tested i'm getting...
