NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
I'm working with a nrf9160 custom board device using the nRF cloud location service. I'm trying to use the nRF cloud API GetLocationHistory endpoint to retrieve the previous...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hello,
I am currently testing the `ipt_initiator` sample on the nRF54L15-DK v1.0.0 using nRF Connect SDK v3.3.1.
When I call `k_sleep()` inside the loop in the `main(...
Hi guys,
I got very strange problem:
I got 2 units:
1) "Tester" board (which is a CENTRAL)
2) "TOP" board (which is PHERIPHERAL)
The "Tester" get commands...
Hi,
1.Can the sQSPI and SPI functions of nRF54L15 operate simultaneously at 32 MHz on the P2 port? 2.Can the sEMMC and SPI of nRF54L15 operate simultaneously at 32 MHz on...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
Hei!
I can't seem to get my devicetree overlay to properly work. I have an external LED and two buttons connected to the GPIO ports mentioned in the overlay, and I've...
Bros, I had updated ncs sdk from v3.1.1 to v3.3.1 today, and when I rebuild an nrf5340 project found that NETAPP ram overflowed, and the error could be represented by build...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
Using SDK 2.4.2
1) Is there a way to specify multiple MCUBoot keys in the same way they can be specified for NSIB? MCU Boot allows an array of keys, but it looks like zephyr...
Hi! Do people actually use the 2.2-4.7Ohm series resistor on the VBUS input to the nRF5340? It's just such a low resistance, I don't particularly see the point. Thanks!
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
