I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hello everyone,
my application is build based on the mulitrole example. The device name is somehow limited to 4 letters.
I checked:
init.advdata.name_type = BLE_ADVDATA_FULL_NAME...
Hello, I attempted to enable the zephyr task watchdog model but whenever I configure it to enable the hardware watchdog module I get the error above. Any idea why I am getting...
Board: NRF52840
SDK: 16
Soft Device: s113
So our board is custom and does not contain a crystal. We are treating P0.00 and P0.01 as GPIOs for button inputs. P0.01 works...
Hi all,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
Hello, I tried to implement the zephyr executing time functions API on my nrf52 hardware and I got the above error. According to my SoC documentation (nRF52833), this hardware...
Dear Devzone:
I am developing the design of a PCB that implements the nRF9160 SiP module, I have doubts about how to make the communication interface to connect the module...
Hello,
I used the nRF Connect plugin for VCS to create a Zephyr/BLE project. It appears this copies many files into the "build" directory which are required to compile the...
I am getting compilation errors when using the DT_ macros to access SPI bus child entries.
Overlay file:
&spi1 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin...
hardware : nRF52840DK-52840
SDK : NCSV1.7.1
IDE:Visual Studio Code
I wanted to printf float value , so I set CONFIG_CBPRINTF_FB_SUPPORT=y in my prj.conf file, my application...
Hello,
I'm using following code to read ADC values. The minimum sampling time I'm able to read the ADC reliably is 60ms. I want to lower it to say 5ms or 10ms.
Is there...
To the kind attention of Nordic support team,
reading at this: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrfxlib/softdevice_controller/README.html#softdevice...
Hello,
I have I am trying out the LPN sample from nRF5 SDK for Mesh v5.0.0 and I have an issue where certain mesh configuration messages (e.g. set publication, add application...
