After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
In nrf_gpiote.h:
The workaround code for PAN_028 OUTINIT anomaly (#9) will cause the GPIO to glitch to the undesired state if it is already assigned to a GPIOTE and in...
I'm trying to use the NOACK mode for some packets on the transmitter side,
and W_ACK_PAYLOAD on the receiver side.
My problem is that if the receiver gets a packet with...
Hi,
mi question is about how to configure in a good and complete way Timer1 and Timer2, so trying to be more specific with my Question:
I need timers with a Tick of 250ns...
We are creating the source program for examining RF module which uses nRF24LU1P.
It is the program that it transmits on the frequency specified from PC.
The API of USB...
I'm attempting to write my own Service based on an example; there are two simple Characteristics in the design. During the discovery process, however, I'm getting the following...
Recently i have bought 4 nRF51822 custom board and unable to program it.
The laser mark of the nRF51822 for custom board is
N51822
QFAAC0
1308AE
I failed to program...
My 51822 needs to support some realtime control code that runs for about 75mS. During that time I need to mask all interrupts. With a logic analyzer I can see that my realtime...
I was trying to find nrf51822's operating distance range (max) in the Bluetooth LE mode. Couldn't find any from the documentations.
Any theoretical numbers and/or practical...
So I am trying to figure out what i do and dont have access to as far as flash and ram is concerned. From the nRF51822 spec it discusses this in general but im finding myself...
Hi
My name is Bernard Britton from Trinidad & Tobago and I am looking for someone competent with nRF9E5 to develope a wireless potentiometer position sensor with LCD receiver...
Hi,
While the softdevice is active (nRF51822) available interrupt priorities are:
typedef enum {
NRF_APP_PRIORITY_HIGH = 1,
NRF_APP_PRIORITY_LOW = 3
} nrf_app_irq_priority_t;...
Hi all,
I'm trying to use NRF24L01, using REUSE_TX_PL command,
the data sheet says as long as CE keep high, the chip will transmit the payload continuously, what i wondering...