Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
Is the nRF9160 capable of operating on the CBRS band (b48)?
I know it is not listed as a band that is supported by HW but I am curious if there is a software workaround...
Hi Nordic Team,
I am working on the BIS demo, I have three nRF5340 DK audio boards, so I set one as Source, two others as Sink, so is there any resources that when Source...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
Hi devzone
there are 2 nrf52 dk board - one is client(ble_app_blinky_c) and the other it peripheral(ble_app_blinky)
and I made it so that if you push the button3 on...
I need to port some functionality that is using nRF5 SDK 17.0.2/ S332 SoftDevice v6.1.1 to an older firmware using nRF5 SDK v12.0.0/Softdevice 332 v2.0.0. It looks like Softdevice...
I'm trying to build the documentation on a Windows 10 system. I've installed all of the required tools and made it to step 4 when I get the following:
C:\ncs\v1.9.1\nrf...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
I'm having problems reading channel AIN7 in the rRF52, SDK11
I configure every channel in a similar way:
//adc_channel_5
{
nrf_saadc_channel_config_t channel_config...
Hi I am working on nrf52840 dk project. I want to find out the maximum stack usage of the program.I searched in the devzone support forum and stumbled upon this method to...
Is there a problem with writing-to and notifying-from the same characteristic? Or is it recommended that one create two characteristics, one for receiving data, and the other...
Hi everyone,
I am using the nRF52840-PDK and nRF5_SDK_17.1.0_ddde560, And trying to enter System Off modes with no RAM Retention.
I use the ram_retention example from...
Hi,
I have met a problem that I try to advertise nRF52840 dongle in pc-ble-driver-py. However, connection is not built from this command:
The uuid is uart over ble which...
Hello Nordic family, I hope everyone is fine.
I want to do modifications to the nRF Toolbox android App such that the data received by the nRF Toolbox android App from the...
I'll start off by saying, as a new developer, Nordic has made an absolute mess out of the docs. The default example 'TWI_sensor' starts with easyDMA enabled, meaning it defaults...
