Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello I have developed a project that was initially based on the nRF52810 for an Indoor Air Quality Data Logger(IAQ-LOGR) which monitors Ambient Light, Temperature, Humidity...
I designed a PCB with only the nRF52833 chip and antenna. I want to learn about the relationship between different TX power levels and the overall power consumption of the...
My board is nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
At this development stage I want to measure continuously incoming frequency ranging from 1Hz to 1MHz with high...
Hello,
I have a scenario where I use crashlog but not flashlog.
My application is crashing in nrf_log_backend_crashlog_panic_set during log_msg_queue_process(mp_flashlog_queue...
Hello
I was working on a project, trying to enable the power management but I could not. So I just tested the simple zephyr sample application device_pm just to see if there...
Hello. We are testing the example of bl provisioning provided by sdk v2.8.0.
When the first wifi is connected, the wifi's data is stored on the board, and even if you turn...
Hello Nordic Team, I am working on a LE Audio project on NCS v2.9.0. My development board is nrf5340-dk. I am using unicast client example and I am trying to use it with my...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Hello, I have recently switched to nrf52840 dongle for 802.15.4 sniffing.
I did a simple test with a ZigBee Green Power sensor sending data on channel 11. On the receiver...
Hi,
I am using a nrf52840 dongle for sniffing the bluetooth connection between 2 devices. These are the wireshark logs
What I could see is it initiates the pairing with...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
