Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
I am working on nRF51822, SDK12.3.0 in IAR workbench.
I am use init pin 2 as an interrupt.
Device will advertise for 20 minute after 20 minute device go to sleep...
Platform info: SDK153, MESH 3.2 and using SEGGER RTT for debug logging output with __LOG(...)
I have a strange behaviour in one of my application, where it work very fine...
Hi,
I am using nrf52 Bluetooth to transfer the data .Here i am not getting how to transfer the data at 10ms through Bluetooth.
Is there any example program to transfer...
Hi,
I'm evaluating a custom PCB that uses the MDBT50Q (nRF52840) and I'm really stuck. It looks like the device is working, but I'm getting a few strange issues.
Out of...
Dear,
we are developing a beacon product with nRF52832 powered from Li-SOCL2 primary battery. I understood that We cannot connect directly battery to the nRF52832 beacause...
Hi,
Anybody managed to connect a WisNode RAK811 to an nRF52840-DK and make them "talk" ? (send "at" commands to the RAK811 shield and get replies)
How did you connect...
Hello Nordic Community,
I am using latest firmware mfw_v1.0.1 latest NCS tag (v1.0.0) as well. I flashed GPS example into DK successfully. I made custom hardware using nRF9160...
Hi,
I am using ncs 1.0.0 and Modem FW version 1.0.1.
I am using UART 2 and i have kept UART TX and RX port 0.11 and 0.10 in overlay file.
I want to change the port pins...
Hi,
Our team has identified an opportunity that your nRF52832 fits well, I am having a difficult time getting started with your Bluetooth SDK and reaching out for assistance...
Hi,
As simple as the title! I have tried to move my code from sdk v 3.1 to v3.2 but it will not join the network.
Back to basics and using off-the-box ligh switch example...
Hi
I have been working with the nrf52832 breakoutboard from sparks fun and the nrf52 10040 Dev board.
I want to work with SPI communication in order to intergrate an accelerometer...
I'm having an issue with some iPhone11's, where under certain conditions the iPhone11 is sending two consecutive Link Layer requests with a Control Opcode of 0xFF. The SoftDevice...
Using zboss_start_no_autostart() instead of zboss_start() will cause a power consumption of 630uA. I was expecting the device to be sleep and in a very low power mode.. All...
