Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
As part of the NCS install, in the ncs\vx.y.z\Zephyr\doc folder there is a ton of Zephyr documentation (more then 13MB) in .rst format. How do I use this instead of the online...
Hi all
I've tried to build the nRF5340: Multicore application on different host platforms using the nRF Connect SDK v2.1.0. It worked without any problems on Windows and...
Hi,
I'm using NRF52832 with s132 softdevice for a low power project. I notice that when running firmware with DFU Buttonless, the SoC consume more power than without it...
Hi,
I'm trying to reproduce the fatfs example on a nrf52840 DK and Sandisk micro SD card that's plugged into a Sparkfun Transflash breakout board. I can't seem to mount...
Hi everybody,
I'm working on a project where I want to write in an external flash nor memory, and transfer data over BLE. The combination of the peripherical_uart sample...
Hello,
I need to sample 2 saadc channels at 6Khz, and another saadc channel at approx 1/sec for a battery measurement. Which are configured for channels 0,1 and 6 respectively...
Hello all I am using nRF52832 I am using SEGGER Embedded studio for programing. I want to use pins 12 and 11 as Rx and Tx for UART. I changed the default pins to #define RX_PIN_NUMBER...
Hi,
Two weeks ago, I've tested my new devices in an anechoic chamber. I'm using Fanstel BT840X modules. These modules are using nrf52840 for MCU/Radio and SKYWORKS SKY66112...
Dear Nordic Support
I scanned through the DevZone Topics, and found a few tickets concerning MQTT-SN support.
As far as I have seen, MQTT-SN was once supported in the...
How can I enable a matter accessory device to actively send data to a matter control?
I'm using matter-lock sample to test the method of sending data from the matter-accessory...
Hello I have seen ALOT of posts referencing to first build and run ble peripheral uart example and then from there that it will be easy to remove the uart from the functionality...
Task description
I would like to use RTC2's COMPARE_0-event to trigger SAADC's conversion task via PPI, continuously. The RTC needs to operate by itself without CPU intervention...
Hello,
I'm using nRF52840 DK (Central) and nRF52840 Dongle(Peripheral). Dongle flashed with Simulation program which transmits data. DK flashed with hci uart controller...
Hi,
Are there any Thread compatible nRF chipset that are footprint pin compatible wityh nRF52832? I understand/interpret that it is not possible to Firmware upgrade 52832...
