Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I am using a custom NRF5340 board and trying to run SPIS related code. The issue I am facing is that MISO pin kept low during the complete transaction . My pin configurations...
Hi, I have been getting randomly errors status from pmic measurements including status 64 (trickle timeout, I presume). Do you have any sample code to handle errors as per...
This is a custom board with nRF54L15. I have the following peripherals connected:
I2C30 SDA:P0,02 SCL:P0.03
I2C20 SDA:P1.13 SCL:P1.12
UART00 TX:P2.02 RX:P2.00
I also...
Hello,
Currently designing in the npm1300 into a project and want to understand better the difference between the LDO and the load switch. In the example schematics the...
Hi
Since the Vout setting range is 1V~3.3V, and the datasheet Figure 39 show the dropout voltage is ~60mV(0.06V)
Why datasheet LDO electric spec. show the VIN need larger...
Folks,
We have been developing a product to use the nrf51840 Dongle. Idea being to solder it to a mother board and as it's pre certified we don't have to go through RF certification...
Hello, I'm building the sample Measure battery voltage on a custom board, and I have an error voltage: setup: -134 at runtime. The overlay file is configure as explained in...
I want to implement OTA (Over-the-Air) updates using Thread on the nRF52840 DK board.
Are there any sample codes or references available for achieving this with Thread?
Hello,
I'm trying to use nRF9160 Development kit and it is not showing up in connected devices view in VS code.
Switch position is correct(nRF91) on the development...
I am using v3.0.2 SDK, nrf52832 DK, and I am learning academy.nordicsemi.com/.../ . I encountered a problem in step 4.2:
Please help me find out how to debug
With the NRF_CLOUD_MULTI_SERVICE sample, we'd like to set the GNSS location tracking sample interval to 2s or even 1s.
But we found that the actual time will be about 25s...
Hello everyone, I need to attach a QSPI memory to an NRF54L15 module. I am led to believe that this should be supported out of the box but cannot understand how to use the...
Hello everyone,
I am working on a project where I need maximum range and TX power, since my Bluetooth device will be implanted the signal is strongly attenuated I need maximum...
Hi,
We are evaluating the NRF9151 for live tracking purposes. While testing with the nRF9151-DK we noticed the we had tracking fallouts using AT#XGPS=1,1,1 both during driving...
