I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
The SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does...
Hello guys
I tried to start TWI bus and got a lot of questions. (NRF51 1422 AC)
I added necessary libraries, could You tell me what more i need to include in my code ...
Hi , We are using NRF52832 for our product .I have a small doubt in using GPIO . Can we use PORT and PIN events simultaneously at a time .
I need to configure some pins...
Hi,
I have three beacons in my setup:
One listening (R1) and two transmitting (T2, T3). T2 and T3 transmit packets with same length.
Say, T2 has started transmission...
Hello,
My system is one device with multiple host, these host will connected to the device on irregular basis.
The host action are listed below:
scan->connect->write data...
hi, i'm going to do some project with nrf51822 and SDK 6.0.0.
i just made up ble connection between phone and the chip.
and i want to send data some fixed time periods...
Hello,
I think there's a bug in the app_uart library in SDK 10 that occurs when the FIFO is enabled.
Using SDK nRF51_SDK_10.0.0_dc26b5e, I was trying to write data to...
I'd like to control a DC motor using PWM (PWM0, pretty straight forward).
To determine motor speed I disable the PWM every 5ms (TIMER1, pretty straight forward) and measure...
Hello,
Our application consists of 100 BLE static centrals and 1000 BLE moving peripherals. Is it possible to hide our BLE peripherals to be visible only by our centrals...
Hi,
i'm testing an application on nRF52, with nRF5_SDK_11.0.0-2.alpha and SoftDevice 132.
I took the ble_uart example and added a custom service with some characteristics...
Hello,
i'm trying a bluetooth connection between nrf UART v2.0 installed on my phone(android 4.4) and nRF 8001 (i'm usign nRF2740 card). My microcontroller is a STM32....
Hi.
I made my own board using nRF51822AC.
I want to connect this board to PCA10028.
There is Debug OUT port(P19).
Net names are EXT_VTG, EXT_GND_DETECT, EXT_SWDIO, EXT_SWDCLK...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I'm testing External interrupt.
Current concumption was just 50uA around(low speed advertising mode).
But It goes 1mA around...
