Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi. I have some question regarding to Bluetooth 5.4 on Nordic platform
1. Can Nordic platform do Advertising Coding Selection? I saw some old old issue that the device...
Hi,
I have tried to update the nRF Connect for Desktop app (v.4.2.0 to v.5.0.2). Unfortunately, the process does not work through the end. Once the installation of the new...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
Hello,
I have connected a LSM6DSO sensor to my nRF52805 which is powered via GPIO. At startup zephyr RTOS wants to init the sensor and failed. After a reboot it detects...
On the SDK 17.0 NRF52840 platform, using sd_temp_get to read the chip temperature works correctly. However, if the sd_clock_hfclk_request function is used in subsequent operations...
Hello,
I'm trying out the example code "pin_change_int_pca10056". But the delay time between sensing a voltage change and toggling the output GPIO is quite long. 22us. Is...
I wanted to know in what ways can I connect thingy:53 to nrf9160 dk via Bluetooth? I understand that dk has onboard nrf52 and hence thingy:52 could get connected wirelessly...
Hi all, I am using the nRF52840 and I came across the nrf52_handle_approtect() func in modules/hal/noridc/nrfx/mdk/system_nrf52.c.
In the nrf52_configuration_249() function...
Hi,
I am unable to access P0.09 and P0.10. I face a similar problem to this thread . I've declared CONFIG_NFCT_PINS_AS_GPIOS=y in prj.conf. Also I've checked 0x1000120C...
i have a custom board that uses a nrf5340 that has been hardware modified so i can work again on getting my board to draw the mimimum power from the battery.
i have a PPK2...
I am using nRF5 SDK (17.1.0).
The MTU size is set to 53. I am using sd_ble_gatts_hvx() to send 16 bytes of data via Notification.
When I check the received data with the...
Hi,
Our product is currently undergoing FCC and ISED certification with Dekra. They are asking for 58741REM.001, 59675REM.001 and 64610REM.003A1 reports for reference. Can...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
